PIC Programmer
Description:
This is bobblick.com's version of the classic PIC 16C84/16F84 programmer. The design is originally by David Tait.
Application:
PICs are small microprocessors containing RAM, ROM, and some peripherals. Almost no other parts are required to make a complete “embedded system”. They are readily available and well supported by the manufacturer, third party developers, and most importantly, users. This has led to their immense popularity.
Assembly:
The PC board design is fairly straightforward and can be made by laser printing to special paper or a page from TIME magazine, then ironing the image onto copper-clad board, then etching with ferric chloride. There are a few jumper wires. The power source needs to be at least 15 volts. A 12 volt DC adapter usually produces about 17 volts, so that's a good choice. Two 9-volt batteries in series will work too. Solder directly to the PC board or use a connector that mates with your power source. Pay attention to the direction of the voltage regulators because the plastic regulators are backward from the tab type. Substitute Japanese or European generic equivalents for the transistors and diodes, but remember that the pinouts will be different. A right angle PC mount DB-25M connector is specified, but a conventional solder-cup DB-25M connector works.
Operation:
The programmer connects to the parallel printer port of your computer and requires external power. If you want to program a PIC you'll have a hex file created by your assembler or created by someone else. You will also need to drive the programmer with some software. Here are programs that run under DOS and Windows. Linux software for Intel-based computers is available elsewhere. Macintoshes do not have parallel ports and can't use this programmer. Do not insert the PIC to be programmed until you have power applied and have run the software, and the programming LED is not lit. The DOS software requires command line switches for fuse settings(unless in the chip's hex file)and also the environmental variable "set ppsetup=3" to be typed before running the program. The Windows software requires the driver "dtait.drv" to be in the \windows\system directory and also the line "PINAPI=DTAIT.DRV" added to the system.ini file. Tell the software you have 7407 chip and PNP transistors. These details are explained in the text files included with the software.
Here's the required parts list: http://www.bobblick.com/techref/projects/picprog/f84pgm.txt
Download the DOS software: http://www.bobblick.com/techref/projects/picprog/pic84v05.zip
The windows software: http://www.bobblick.com/techref/projects/picprog/picser.zip
Please note: the PC board layout has been updated January 29, 2002 to give more space between pins and traces around the two transistors, and adding R11, required for programming 16F628 and others.
Programming newer PICs:
The whole “F” series can be programmed. You need to use newer software, like this cool software. The PIC16F627 and PIC16F628 are 18 pin devices and fit right in the socket, but you must make a ground connection to pin 10 to prevent LVP programming, a new feature this programmer does not use. Some people suggest using a 10K resistor to ground, if you are doing in-circuit programming that probably makes sense. Programming the bigger PICs, including the PIC16F872 through 16F877 requires fitting the correct(28 or 40 pin) socket and wiring the pins to the corresponding function. Remember to ground the LVP pin on these, too. The bigger PICs also have extra power and ground pins. These must all be used.
You must select the port your computer is using(usually 0378) and the type of programmer (P16PRO) and the type of buffers the programmer uses (non-inverting). The software is beta, but I have tested it and can testify it working on the 16F84 and 16F628 I tried. It only programs locations used in the hex file, so it is very fast. If your program is 250 bytes, only 250 bytes get programmed, but when I used my PicstartPlus to verify the chips I tried, it would show a verify error unless I blanked the chip first, although the chip functioned fine. Leaving those unused areas in the previously programmed state shouldn’t be a problem.
Propic2 keeps the power to the chip on while idle. This can be useful for “burn and crash” in-circuit programming. You’ll see the LED is lit. I don’t like to insert or remove the PIC when power is present, so I pull the power cord before I insert or remove the PIC.
propic2 software, in case the above link is broken.
None.
(OR),
you can order a PIC burner kit(you have to assemble it all,.... pcb will be provided with all the components) for low cost, at kits n spares-
Details: s.no. 64,
PIC Burner:-The Programmer for PIC16X8X Micro-controllers (With Sample Project of Melody Generator): (Sept. 2002):
This kit contains all the necessary items to build a programmer for PIC16X8X series of micro-controllers. PIC16F83, PIC16C84, PIC16F84 and PIC16F84A are some of the many micro-controller ICs from Microchip technology Inc. For demo purpose, one sample project “PIC16F84 Based Melody Generator” is also included here. The programmer and sample project details are explained separately. The programmer software, assembler and general details pertaining to PIC are included in CD. Number of ICs used: 4
Price: 1000INR
http://www.kitsnspares.com/user/default.asp
http://www.kitsnspares.com/user/index.asp?currentpage=1&var=50
(check out s.no. 64)
No comments:
Post a Comment